Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Tub Surround
Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Tub Surround
Blog Article
They are making a few good annotation related to Tools You Need to Install a New Bathtub as a whole in the article underneath.
Installing a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is also a moderately tough job. If the old bathtub is conveniently accessible, the project can move rapidly; if you have to open up a wall surface to get rid of the old bathtub and also position the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have qualified yourself for the job and also fit trying it. Instead of employing a professional to take over a halfway-completed task, it is far better to think about utilizing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly assist you install a new bathtub in your shower room if you have already acquired a brand-new bathtub as well as don't need to change the arrangement of your previous water pipelines.
Your devices as well as material checklist must make up the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the limited access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washers are in area in between the tap as well as the sink. Safeguard the faucet in place with the maker given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The former type ought to be attached to the faucet ends first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of both wooden boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest versatile tap port to the ideal supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as additionally inspect the overflow electrical outlet as well as the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub must wait up until the tub has been utilized a minimum of once as this will settle it into its final position.
Planning for the Installment
To start with, the supporting frame supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final setting.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, causing complications with moisture and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealant can split relatively very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our article about A Step-by-Step Guide to Installing a Bathtub. Thanks so much for finding the time to read our piece. Enjoyed reading our entry? Please share it. Help somebody else locate it. I cherish reading our article about How to Install a Bathtub.
Book-Now
Report this page